Design: Project Development | GSP & Amendments | Division 5
DIVISION5.GR5 SURFACE TREATMENTS AND PAVEMENTS
01.GR5 CEMENT CONCRETE PAVEMENT REHABILITATION
0103.GR5 Construction Requirements
01031A1.GR5 Submittals
(April 3, 2006)
Include in all projects when pH monitoring is a
condition of a NPDES construction permits, a 401
Water Quality Certification, or other permit.
Requires approval of Regional Environmental
Manager and Regional Construction Manager. Must
also use 0105.GR5, 05031B.GR5, 0505.GR5,
023003.GB6, 025A4.GB6, 0103A.GR8, 01031A.GR8,
and 0105,GR8.
0105.GR5 Payment
(April 3, 2006)
Must include with 01031A1.GR5, 05031B.GR5, 0505.GR5,
023003.GB6, 025A4.GB6, 0103A.GR8, 01031A.GR8, and 0105.GR8
02.GR5
BITUMINOUS SURFACE TREATMENT
0201.GR5 Description
0201A.GR5 (Coal Tar/Asphalt Emulsion Blended Sealer)
(August 6, 2007)
Use in projects where Hot Mix Asphalt requires
added protection from spilled fluids such as
solvents, hydraulic fluids, diesel, gas or other
oil products that dissolve hot mix asphalt products.
The typical location for the application of Coal
Tar/Asphalt Emulsion Blended Sealer would be in Rest
Areas or Weigh Stations.
Must also use 0202A.GR5, 0203A.GR5, 0204A.GR5,
and 0205A.GR5.
0202.GR5 Materials
0202A.GR5 (Coal Tar Emulsion Seal Coat)
(August 6, 2007)
Must use with 0201A.GR5, 0203A.GR5, 0204A.GR5 and
0205A.GR5.
0203.GR5 Construction Requirements
0203A.GR5 (Coal Tar/Asphalt Emulsion Blended Sealer)
(August 6, 2007)
Must use with 0201A.GR5, 0202A.GR5, 0204A.GR5 and
0205A.GR5.
020303.GR5 Application Of Asphalt
0203031.FR5 (BST New Construction)
(August 6, 2007)
May use with 0203032.FR5.
Use in projects requiring a Bituminous Surface
Treatment on a newly constructed roadway.
(2 fill-ins)
0203032.FR5 (BST Seal Coat)
(August 6, 2007)
May use with 0203031.FR5.
Use in projects requiring a Bituminous Surface
Treatment seal coat on an existing roadway.
(1 fill-in)
0204.GR5 Measurement
0204A.GR5 (Coal Tar/Asphalt Emulsion Blended Sealer)
(August 6, 2007)
Must use with 0201A.GR5, 0202A.GR5, 0203A.GR5 and
0205A.GR5.
02041.GR5 (BST existing road approaches)
(March 13, 1995)
Must also use 02051.GR5.
Use in BST projects when there are a
substantial number of existing road
approaches to be paved and the extra
cost of labor for paving approaches
becomes a factor in determining the bid
price for BST.
0205.GR5 Payment
0205A.GR5 (Coal Tar/Asphalt Emulsion Blended Sealer)
(August 6, 2007)
Must use with 0201A.GR5, 0202A.GR5, 0203A.GR5 and
0204A.GR5.
02051.GR5 (Bituminous Surface Treatment For Road Approach)
(February 5, 2001)
Must include with 02041.GR5.
Use in BST projects when there are a
substantial number of existing road
approaches to be paved and the extra
cost of labor for paving approaches
becomes a factor in determining the bid
price for BST.
04.GR5 HOT MIX ASPHALT
0402.GR5 Materials
040202.GR5 (Materials)
Must use once preceding 04021.FR5,
and 04024.GR5.
04021.FR5 (Asphalt Binder Content)
(January 5, 2004)
Use in projects with hot mix
asphalt and the Contracting Agency is
providing a source for, or a source for
the production of, mineral aggregates.
(1 fill-in)
04024.GR5 (Open Graded Emulsified Asphalt Pavement)
(January 3, 2006)
Must also use 0403031.GR5,
0403041.GR5, 0403051.GR5, 0403091.GR5,
040310A.GR5, 0403131.GR5, 04041.GR5, and
04052.GR5.
Use in projects with Open Graded
Emulsified Asphalt Pavement.
0403.GR5 Construction Requirements
040303.GR5 Hot Mix Asphalt Pavers
040303A.GR5 (Material Transfer Device/Vehicle)
(April 5, 2004)
Use in projects containing Hot Mix
Asphalt when recommended by the
Region Material Lab and Region
Construction Office. Use requires
approval of the Region Construction Office.
0403031.GR5 (Open Graded Emulsified Asphalt Pavement)
(March 13, 1995)
Must include with 04024.GR5.
Use in projects with Open Graded
Emulsified Asphalt Pavement.
0403032.GR5 (Reference line required for paver)
(March 13, 1995)
Use in projects with a 70 MPH or higher
design speed, except when the paving will
be done under traffic.
0403032A.GR5 (HMA Pavers)
(April 2, 2007)
Use in all projects that contain HMA.
040304.GR5 Rollers
0403041.GR5 (Open Graded Emulsified Asphalt Pavement)
(March 13, 1995)
Must include with 04024.GR5.
Use in projects with Open Graded
Emulsified Asphalt Pavement.
040305.GR5 Preparation Of Existing Surfaces
0403051.GR5 (Open Graded Emulsified Asphalt Pavement)
(March 13, 1995)
Must include with 04024.GR5.
Use in projects with Open Graded
Emulsified Asphalt Pavement.
040305c.GR5 Crack Sealing
Must use with 040305C1.GR5 or 040305C2.GR5.
040305C1.GR5 (Crack Sealing)
(December 6, 2004)
At the region's discretion use at the following locations:
In areas where HMA will not be placed over the crack sealing
such as on shoulders of a grind and inlay project.
In areas where BST will be the only material placed over
the crack sealing such as chip seal projects.
040305C2.GR5 (Crack Sealing)
(December 6, 2004)
At the region's discretion use on paving projects with
prelevel or multiple courses.
040307A.GR5 Mix Design
040307A1.GR5 (Mix Design Verification)
(August 1, 2005)
Use at the discretion of the Region. Consider using
when paving is a critical activity and contract time
does not include working days for HMA mix design
verification. Not recommended for use on projects
with adequate time for mix design verification prior
to HMA placement, or when other mechanisms (such as
a flexible start date) allow verification to be
performed without causing a delay to critical
paving activities.
040308A.GR5 Acceptance Sampling and Testing - HMA Mixture
Must use with 040308A1.GR5 and 040308A2.GR5.
040308A1.GR5 (HMA Evaluation)
(April 7, 2008)
Must also use 040503A.GR5 and 03087.GR9.
Use in projects that add volumetric
properties (VMA and Va) to the statistical
evaluation of Hot Mix Asphalt. Not for
use in projects that contain 2500 tons
of HMA or less. The determination to
utilize this specification will be
determined by the Region Construction staff.
040308A2.FR5 (Commercial HMA Evaluation)
(January 5, 2004)
Use in projects where the area that
commercial hot mix asphalt is to be
used is not identified in the Standard
Specifications.
(1 fill-in)
040309.GR5 Spreading And Finishing
0403091.GR5 (Open Graded Emulsified Asphalt Pavement)
(March 13, 1995)
Must include with 04024.GR5.
Use in projects with Open Graded
Emulsified Asphalt Pavement.
040310.GR5 Compaction
Must use with 040310A.GR5.
040310A.GR5 (Open Graded Emulsified Asphalt Pavement)
(March 13, 1995)
Must include with 04024.GR5.
Use in projects with Open Graded
Emulsified Asphalt Pavement.
040312.GR5 Joints
0403121.GR5 (Feathering Hot Mix Asphalt)
(January 5, 2004)
Use in projects requiring the feathering
of hot mix asphalt.
040312A.GR5 Transverse Joints
(January 3, 2006)
Use in projects when planed lane will
be open to traffic prior to paving.
When using this GSP consider the need
to control the amount of time the planed
area is open to traffic by adding 0403140.FR5
where appropriate.
040313.GR5 Surface Smoothness
0403130.FR5 (Surface Smoothness)
(April 24, 2006)
Use in all projects that contain HMA paving
at the discretion of the Region Construction
Manager. Paving must be a minimum of one
mile in length. For accurate measurements,
the HQ Materials Lab profiler must be able
to move through the sections to be measured
unimpeded at a minimum speed of 35 MPH.
Notification must be made to HQ Materials
Lab Pavements Section in order to schedule
the post paving IRI determination.
Fill-ins #1-6 are to be provided by the
HQ Materials lab Pavements Section. Use with
04042.GR5 and 04053.FR5. Do not use with
0403132.FR5 or 0403133.GR5.
(6 fill-ins)
Contact John Livingston, Pavements
Special Projects Manager at 360/709-5472 to
schedule the IRI determination and to complete
fill-ins.
0403131.GR5 (Open Graded Emulsified Asphalt Pavement)
(March 13, 1995)
Must include with 04024.GR5.
Use in projects with Open Graded
Emulsified Asphalt Pavement.
0403132.FR5 (Smoothness requirements)
(March 13, 1995)
Use in projects with roadways to be
paved that have posted speeds both
greater than and less than 45 MPH.
Do not use with 0403130.FR5.
(1 fill-in)
0403133.GR5 (Smoothness requirements)
(January 5, 2004)
Use in projects with all roadways to
be paved are posted less than 45 MPH.
Do not use with 0403130.FR5.
040314.GR5 Planing Bituminous Pavement
0403140.FR5 (January 5, 2004)
Use in projects when it is necessary to
control the time the planed area will be
open and exposed to traffic prior to paving.
0403141.GR5 (Requires test section and smoothness requirements)
(January 5, 2004)
Use in projects with large quantities
of planing. When using this GSP consider the
need to control the amount of time the planed
area is open to traffic by adding 0403140.FR5
where appropriate.
0403143.GR5 Vertical Edge Planing
(March 13, 1995)
Use in projects when planed lanes shall
be paved prior to being open to traffic.
0403144.FR5 Beveled Edge Planing
(October 23, 2000)
Use in projects when planed lane will
be open to traffic prior to paving.
When using this GSP consider the need
to control the amount of time the planed
area is open to traffic by adding 0403140.FR5
where appropriate.
(2 fill-ins)
040316.FR5 Weather Limitations
(January 5, 2004)
Use in projects when it is anticipated
that paving will be conducted in the Fall.
(1 fill-in) (Fill-in to be provided by Region Materials Engineer)
0404.GR5 Measurement
04041.GR5 (Asphalt CMS-2M)
(March 13, 1995)
Must include with 04024.GR5.
Use in projects with Open Graded
Emulsified Asphalt Pavement.
04042.GR5 (Surface Smoothness)
(April 24, 2006)
Must include with 0403130.FR5 and 04053.FR5.
04044.GR5 (Asphalt Cost Price Adjustment)
(September 5, 2006)
Include in all projects containing Hot Mix
Asphalt.
Must include 04054.GR5 and standard item 5837.
0405.GR5 Payment
0405A.GR5 Must use with 04052.GR5, 04053.FR5, or 04054.GR5.
04052.GR5 (Open Graded Asphalt Pavement Excl. Emulsified Asphalt)
(September 30, 1996)
Must include with 04024.GR5.
Use in projects with Open Graded
Emulsified Asphalt Pavement.
04053.FR5 (Surface Smoothness)
(April 24, 2006)
Must include with 0403130.FR5 and 04042.GR5.
Fill-in is the appropriate Pay Adjustment Schedule
as determined using the criteria below.
Pay Adjustment Schedule 1 = Interstate highways,
new pavement construction or multiple lift pavement
overlays (at least one (1) leveling course + wearing
course).
Note: Pre-leveling allowances are not to be counted
as a leveling course paving lift with respect to this
definition.
Pay Adjustment Schedule 2 = Single lift pavement
overlays with allowance for surface variance
corrections with smoothness averaging devices
(paving skis) or full width pavement milling
(including shoulder) with single lift replacement
overlay.
Note: Sufficient preleveling and/or pavement
thickness variance allowances should be included
to repair obvious existing deficiencies (humps,
valleys, ruts etc.).
Pay Adjustment Schedule 3 = Smoothness will be
difficult to attain or when risk associated with
meeting a smoothness criteria is unknown. Examples
include matching to existing concrete gutter lines;
sections with multiple surface utility structures;
intersections; multiple skip sections resulting in
short paving lengths; and milling/replacement paving
where both the shoulder and adjacent lane is not also
milled. Bonus incentives are applied to encourage
maximum effort to obtain smooth pavements in difficult
applications.
(1 fill-in)
040503A.GR5 Price Adjustment for Quality of HMA Mixture
(April 7, 2008)
Must also use 040308A1.GR5 and 03087.GR9.
Use in projects with Volumetric Acceptance of Hot Mix Asphalt.
04054.GR5 (Asphalt Cost Price Adjustment)
(September 8, 2008)
Include in all projects containing Hot Mix
Asphalt.
Must include 04044.GR5 and standard item 5837.
To determine the Engineers Estimate for this
bid item, refer to the guidance at:
http://www.wsdot.wa.gov/Projects/ProjectMgmt/RiskAssessment/Information.htm
05.GR5 CEMENT CONCRETE PAVEMENT
0503.GR5 Construction Requirements
050301.GR5 Concrete Mix Design For Paving
050301A.GR5 (Combined Aggregate Concrete Gradation)
(April 3, 2006)
Use in all projects that require cement
concrete pavement.
05031B.GR5 Submittals
(April 3, 2006)
Include in all projects when pH monitoring
is a condition of a NPDES construction
permits, a 401 Water Quality Certification,
or other permit. Requires approval of
Regional Environmental Manager and Regional
Construction Manager. Must also use 0505.GR5,
01031A1.GR5, 0105.GR5, 023003.GB6, 025A4.GB6,
0103A.GR8, 01031A.GR8 and 0105.GR8.
0505.GR5 Payment
(April 3, 2006)
Must include with 05031B.GR5, 01031A1.GR5,
0105.GR5, 023003.GB6, 025A4.GB6, 0103A.GR8,
01031A.GR8, and 0105.GR8.